Emergi-lite Survive-All SVX-HZ Series Manuel d'utilisateur télécharger pdf

Emergi-Lite Tel: (888) 552-6467 ext. 547 or 255 Fax: (888) 867-1565 www.emergi-lite.com

06/07 750.1300 Rev. A

1/4

SVXHZ Series – Exit Sign

AC/DC & Self-Powered Models

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should

always be followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. Do not let power supply cords touch hot surfaces.

2. Do not mount near gas or electric heaters.

3. Use caution when handling batteries. Avoid possible shorting.

4. Equipment should be mounted in locations and at heights where it

will not readily be subjected to tampering by unauthorized personnel.

5. The use of accessory equipment not recommended by the manufac-

turer may cause an unsafe condition.

6. Do not use this equipment for other than intended use.

7. All servicing should be performed by qualified service personnel.

SAVE THESE INSTRUCTIONS

Installation Instructions

1. Turn off unswitched AC power.

Ceiling Mount

a. Remove j-box assembly from carton. Remove j-box cover from j-

box assembly and retain securement screw.

b. Install junction box and route unswitched AC circuit wires into the

junction box and leave 6” of wire length.

c. Remove lens, exit panel and diffuser panel on the front of the unit

(use the supplied bit to remove the tamper-proof screws).

d. In order to access the knockouts of the frame, remove the 4 elec-

tronic module screw(s) holding the electronic module to the frame

and separate them (see fig.2).

e. Remove knockout on top of the frame. Determine which holes in

the exit frame will be used for mounting (see fig.1). Support frame

by two blocks of wood, maximum one inch apart. Strike knockouts

with a hammer and screwdriver. Clear holes of burrs to allow

proper assembly of nipple/wire assembly.

f. Secure j-box cover to the frame using the provided nut.

g. Reassemble the electronic module inside the frame.

Figure 1

Part List

1. Tamper-proof screws short

(4 per lens)

2. Tamper-proof screws long

(2 per lens)

3. Lens

4. EXIT panel

5. Diffuser panel

6. Frame

7. Electronic module

8. Electronic module screws

(4)

9. Backplate (single face sign

)

10. Backplate tamper-proof

screws (4)

11. Lock-nuts (2)

12. Junction box gasket

13. Junction box screws(2)

14. J-box Cover

15. Nipple

16. Juction box

17. Hub

Figure 2

1 2 3 4

Résumé du contenu

Page 1 - SAVE THESE INSTRUCTIONS

Emergi-Lite Tel: (888) 552-6467 ext. 547 or 255 Fax: (888) 867-1565 www.emergi-lite.com06/07 750.1300 Rev. A1/4SVXHZ Series – Exit SignSVXHZ Series –

Page 2 - SVXHZ Series – Exit Sign

SVXHZ Series – Exit Sign2/4Emergi-Lite Tel: (888) 552-6467 ext. 547 or 255 Fax: (888) 867-1565 www.emergi-lite.com06/07 750.1300 Rev. AWall Mount (Sin

Page 3 - Maintenance (All Models)

SVXHZ Series – Exit Sign3/4Emergi-Lite Tel: (888) 552-6467 ext. 547 or 255 Fax: (888) 867-1565 www.emergi-lite.com06/07 750.1300 Rev. ANexus modelsRef

Page 4 - Double Face Installation

SVXHZ Series – Exit Sign4/4Emergi-Lite Tel: (888) 552-6467 ext. 547 or 255 Fax: (888) 867-1565 www.emergi-lite.com06/07 750.1300 Rev. ADouble Face Ins

Commentaires sur ces manuels

Pas de commentaire

Emergi-lite Survive-All SVX-HZ Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fournisseurs d'énergie Emergi-lite Survive-All SVX-HZ Series. Emergi-Lite Survive-All SVX-HZ Series User Manual [fr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fournisseurs d'énergie Emergi-lite Survive-All SVX-HZ Series