Emergi-lite Premier Series - Exit Sign Manuel d'utilisateur télécharger pdf

Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com

11/09 750.1372 Rev. B

Premier Series - Thermoplastic LED Exit Sign

1/2

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

taken including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. Do not use outdoors.

2. Do not let power supply cords touch hot surfaces.

3. Do not mount near gas or electric heaters.

4. Equipment should be mounted in locations and at heights where it will

not readily be subjected to tampering by unauthorized personnel.

5. The use of accessory equipment not recommended by the manufacturer

may cause an unsafe condition.

6. Do not use this equipment for other than intended use.

7. All servicing should be performed by qualified service personnel.

SAVE THESE INSTRUCTIONS

Installation Instructions

1. Turn off AC power.

2. Route AC unswitched circuit of rated voltage into electrical box and leave

6” of wire length.

3. Remove the exit door using a coin or a screwdriver at the top or bottom

of the door.

4. Determine the mounting position (end, wall or ceiling). Note: canopy is

required for end or ceiling mount.

5. Our system can accept input voltages of 120 VAC or 277 VAC. There-

fore, connect the black (120 VAC) or orange (277 VAC) and white (com-

mon) leads to the building utility. Connect the Green wire to the ground.

Unused primary wire must be insulated to prevent shorting

Wall mounting

a. No canopy required. With the help of a flat head screwdriver, knock

out the proper hole pattern in the back cover to mount to a standard

junction box (See Fig. 2). Feed the AC supply leads out through the

center hole and make the proper connections. Feed the excess wire

into the junction box and secure the back cover to the junction box

using the junction box screws. Proceed to step 6.

End or ceiling mount

a. Canopy required. Attach the spider plate to electrical box with the

junction box screws. Remove appropriate hole plug. Feed AC supply

leads through side or top opening and then through canopy. Snap

canopy on top or side of frame (See Fig. 3). Screw canopy to

frame(11). In the case where a canopy lock is supplied, you may

refrain from screwing the canopy to the frame and simply snap the

Figure 1

Premier Series - Thermoplastic LED Exit Sign

AC, AC/DC or Self-Powered

Figure 3

Figure 2

FLAT HEAD SCREWDRIVER

KNOCK OUT

GROOVE

CANOPY HOUSING SCREW

Part List

1. Back plate

2. Frame

3. Diffuser panel

4. Exit door

5. Hole plug for Canopy

6. Canopy

7. Junction box screws (not

provided)

8. Spider plate

9. Junction box

10. Canopy plate screw

11. Canopy housing screw

12. Canopy lock

1 2

Résumé du contenu

Page 1 - SAVE THESE INSTRUCTIONS

Emergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com11/09 750.1372 Rev. BPremier Series - Thermoplastic LED Exit Sign1/2IMPORTANT

Page 2 - Maintenance

Premier Series - Thermoplastic LED Exit SignEmergi-Lite Tel: (888) 552-6467 Fax: (800) 316-4515 www.emergi-lite.com11/09 750.1372 Rev. B2/2canopy loc

Commentaires sur ces manuels

Pas de commentaire

Emergi-lite Premier Series - Exit Sign Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Fournisseurs d'énergie Emergi-lite Premier Series - Exit Sign. Emergi-Lite Premier Series - Exit Sign User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Fournisseurs d'énergie Emergi-lite Premier Series - Exit Sign